Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
Can you believe that this amazing wine rack the image below has been built using old wood pallets? Perhaps you can. Isn’t it wonderful that your old wood pallets can be reused to build something so beautiful and useful? I am not a drinker but I liked the idea so much that I just couldn’t resist making myself one. Although later I gifted it to my parents, who totally loved it.
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular finishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each finish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and finish combinations. Plus: How to stain wood evenly.
Clamping up four mitered corners is tricky. You can buy specialty clamps for this, but I make my own. Here’s how to do it. Start with a long 1×4, as it’s easier (and safer) to clamp for making the angled cuts than a short piece. Mark out the blocks, and then drill a 1-in. diameter hole in the center of each one. The hole prevents the blocks from getting glued to your project. Cut 45-degree angles tangent to the hole, and then cut the blocks free from the long board. We’ll walk you through how to make one for your home shop.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
I built my first platform bed by following the steps mentioned in the tutorial and the end result was everything I expected. It was as beautiful as comfortable and strong. It only cost me around $60 to build this one from the scratch. And if I can build it, anyone can. What you need is a little bit of woodworking experience and a lot of confidence. Collect the items as suggested in the video and start working now.
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.

There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
The Saw Guy - Saw Reviews and DIY Projects Copyright © 2019. Copyright text 2018 by The Saw Guy - Saw Reviews and DIY Projects. TheSawGuy.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Full affiliate disclaimer here
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.

Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.


It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project.
​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.

I know this seems really simple and you may already know how to read a tape measure so just hear me out on this one! Often times with woodworking you need to make exact measurements and cuts and it’s rarely pretty even numbers like 15 inches or 15 1/2 inches. It’s usually like 15 5/8 inches or 15 9/16 inches. So, really knowing how to read a tape measure in its entirety is important. And I’ve created a quick post on how to read a tape measure the easy way along with a helpful free printable.

Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
Instead of using a container to mix a small amount of epoxy, just make a mixing surface on your workbench using painters tape. Simply lay down strips, overlapping the edges so the epoxy doesn’t get on your bench. When you’re done, peel off the tape and throw it away. This mixing surface will work for more than just epoxy, you can use it for wood glue or any other material you need easy access to while working on a project.
Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
Finally, properly preparing your wood surface is super important. It will make a huge difference when it comes times to stain, paint, or finish your wood. There are a lot of tips for wood surface preparation, but sanding the wood is one of the most important steps. And I find it really helpful to do the bulk of my sanding before I start ripping (cutting) and building with my wood since it’s still in whole pieces. You can check out my simple tips for how to sand wood in my how to stain wood tutorial, which is also good to reference if you need to learn how to stain too!
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
Isn’t this amazing that instead of having to throw that old furniture piece away, you can now reuse it to build something even more beautiful? If you do not like this particular idea, there are many other re-purposeful furniture items you can build from an old dresser. Just search the internet for other DIY project ideas. Here is a link to the video tutorial that explains the same procedure in a more practical manner that you can easily follow through.
Hard to determine which stain you need in that bespattered collection of cans? An easy-to-make “stain index,” courtesy of reader Bob Jacek, solves the problem. Section off boards of your favorite woods into squares with masking tape, and apply the different stains across the width of each wood type (pine, oak, birch, etc.). When the stains are dry, brush on lengthwise your regular finishes—polyurethane, water-based polyurethane, oil, orange shellac, etc. You’ll be able to tell how each stain looks with each finish. Label each one. Use both sides of each board, and you’ll have a wooden encyclopedia of stain and finish combinations. Plus: How to stain wood evenly.
See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products See Products

woodworking plans

×